Flat Screen TV Cord and Cable Power Kit
Flat Screen TV Cord and Cable Power Kit is rated out of 5 by 3.
Tidy up your entertainment system with this power kit that features a pre-wired design for easy installation. All the tools you need to conceal cables for a neat appearance are included. No Electrical termination required: Plug and Play. The easiest solution for running flat screen TV power and low voltage cables in-wall. Kit includes 'plug and play' power harness and also allows you to run low voltage cables such as HDMI cables and other component cabling in the wall and out of sight - no electrician or hard-wiring required.
20 In Stock
Added to Your Shopping Cart
- Simple installation: Do-it-yourself kit allows for neat and easy installation in under 30 minutes with no electrician or hard wiring involved.
- Pre-wired all inclusive kit: All parts and tools needed for installation are included in the kit, including a pre-wired power cable.
- Hide low voltage cables: Perfect for hiding low voltage cables such as HDMI and other component wires.
- Kit Includes: 2 power grommets with a 54'' harness, 6' power cord, hole saw and fish tape.
- This product meets the material restrictions of RoHS.
|Countries Of Origin||China|
|RoHS Conformant||Yes||This product meets the material restrictions of Article 4 of the RoHS Directive (2011/65/EU), including Commission Delegated Directive 2015/863.|
Listing Agencies / 3rd Party Agencies
Rated 1 out of 5 by Cashaffer21 from Overall great concept, initially a pain to install I initially bought this product due to the “ease” of installation boasted on the packaging. Everything was going great until it came time to fish the power cord through the holes I cut. (At this point I was committed, so no going back.) The first difficult task I encountered was getting the supplied fish tape fed through the hole to line up and come out the other end. An exterior wall with insulation poses quite the obstacle. After several attempts I successfully retrieved the fish tape (I had to fit what I could of my hand through the hole to blindly feel for the fish tape) and inserted the power cord onto the hook of the fish tape. As I pulled the power cord through the hook became straightened and released the power cord. Now I had to retrieve a half fed power cord through one end and the damaged fish tape through the other. Attempt #2: I successfully fed the fish tape through, same issue as before, connected the power cord to the the hook, but this time I used twist ties to assist keeping the power cord and hook together. As I retrieved the fish tape I could feel the insulation pulling, tearing, and bunching up inside my wall. Just as the fish tape neared the exit hole the hook broke. Lucky for me the cord was there and I pulled the line through. Now I needed to pull my HDMI cords through, but thanks to the bunched up insulation in my wall I cannot get the fish tape fed from one hole to the other. Frustrated and 1.5 hours in on a .5 hour project I gave up. Time to re-engineer this concept and find a way to be able to watch TV with a successful wall mount sans exposed cables. Concept = 5 stars. Ease of installation = 1 star!
Date published: 2019-02-24
Rated 3 out of 5 by Joe D from Now that it’s done I love it, but a pain to instal I love that I was able to install myself and achieve the look I wanted. But this was a pain to install. They make it look easier than it is in the instructions and video. It took about 50 tries to get the wire fed from one hole to the other. Not an easy task when there is insulation in the wall. And one thing that wasn’t mentioned in the instructions, but I was reminded in installation, is that your outlets likely have horizontal wires that attach one to the other. I wasn’t real comfortable feeding the wires across that. I purchased two sets of these, but I’ll be taking my second set back as that room has paneling and these don’t install into paneling. It would be easy to include an adapter for paneling. It’s something you should think about doing.
Date published: 2020-04-27
Rated 5 out of 5 by Johan from Perfect for wall mounting a TV. Finally decided to mount my TV to the wall. Unfortunately, I learned the hard way that I have plaster walls. This made installation a huge hassle. Because of this, I found the hole-saw that came with it useless for this, as it wasn't good enough to get through that much material - even when coupled with a hammer drill. I ended up using two additional hole-saws for my application, but that is not the fault of this kit. If I had drywall this would have been much more simple and could probably have used the included hand hole-saw. After getting past those issues, this kit was perfect for running in-wall power and hiding a few HDMI cables. I also painted the rings to match the color of the wall.
Date published: 2018-06-19
I need additional length of low voltage wiring. Is it available?
Based on the product category I'm not confident I fully understand your question. Please call us at 1-800-621-0049 and choose option 3 from the main menu for technical support. Thank you!
Date published: 2020-06-25
Hello i wanted to know if it is possible to unlock the wall grommet locks so i can turn the bottom wall grommet right side up and tighten it back down thanks.
Yes. Pry off the snap-on trim ring, loosen the screws, pull out and rotate the assembly, tighten the screws, and snap the ring back on.
Date published: 2020-06-21
Will this work with a Samsung right angle power cord?
Good question! Yes, it will. BUT...Samsung is now using a “sideways” right angle plug on some TV’s, which is not compatible. You can identify it by the cord entering the side of the plug. The workaround is buying a compatible right angle cord on Amazon.
Date published: 2020-06-21
In trying to install on a paneled wall. Do you make adapters for paneling? I can see how different clips would make this possible.
The CMK70 Power Kit is designed to fit into walls constructed of a minimum of 2" x 3" studs and 1/2" inch drywall. We do not offer adapters for other wall types.
Date published: 2020-04-27
is there an adapter I can use if the tv plug doesn't fit?
Unfortunately, there is not.
Date published: 2020-01-27
Is this model compliant in New York City?
The CMK70 kit was designed to comply with the National Electrical Code, NFPA70. However, local codes may vary. Please show this FAQ to your local inspector. If after reviewing this FAQ your inspector still has questions please contact Wiremold Technical Support at 800-621-0049 option 3, for further assistance. Here is a link to the FAQ for the CMK70, you may have to copy and paste it in your browser. https://www.legrand.us/-/media/products/resources/wiremold-products/at-home/hide-organize-cords/power-kit/wiremold_cmk70_faq.ashx
Date published: 2019-12-06
I recently moved into a home with this installed, however we would like to move locations. Are there any instructions on how to re-locate? Appreciate any help, and if it is easy might do these in all the rooms of my home.
If you are able to remove all the components of the CMK70 from the existing location undamaged, then you can re-install them in another location following the installation instructions that come with a new unit (link below). However, we do not have actual instructions on how to un-install an existing CMK70. If you need assistance in doing that, please contact Wiremold Technical Support at 1-800-621-0049, option 3. We can you help you with questions about the removal process. https://www.legrand.us/-/media/products/resources/wiremold-products/at-home/hide-organize-cords/power-kit/1010497r2.ashx
Date published: 2018-08-30
I have this grommet kit but unable to lock the grommet in my walls. I have double dry wall in my high rise condo and it is unable to stay in place. Do you have any suggestions?
It's possible that wall is simply too thick and the tab that holds the grommet in place gets past the point where is held captive. When that happens, the tab will just spin around and will not lock in place. That usually happens if your wall is thicker than about 7/8".
Date published: 2020-06-20